![]() ![]() In this article, we examined the GNS3 Layer 3 Switch settings, the most popular network simulator program used to prepare for Cisco exams.Interesting enough, the Catalyst 6500 was not detailed in Figure 2-12. You can watch the video below to use Switch on GNS3 and also subscribe to our YouTube channel to support us! VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2ġ003 tr 101003 1500 1005 0 - srb 1 1002 Interface IP-Address OK? Method Status ProtocolįastEthernet0/0 unassigned YES unset up upįastEthernet0/1 unassigned YES unset administratively down downįastEthernet0/2 unassigned YES unset up downįastEthernet0/3 unassigned YES unset up downįastEthernet0/4 unassigned YES unset up downįastEthernet0/5 unassigned YES unset up downįastEthernet0/6 unassigned YES unset up downįastEthernet0/7 unassigned YES unset up downįastEthernet0/8 unassigned YES unset up downįastEthernet0/9 unassigned YES unset up downįastEthernet0/10 unassigned YES unset up downįastEthernet0/11 unassigned YES unset up downįastEthernet0/12 unassigned YES unset up downįastEthernet0/13 unassigned YES unset up downįastEthernet0/14 unassigned YES unset up downįastEthernet0/15 unassigned YES unset up downġ default active Fa0/0, Fa0/1, Fa0/2, Fa0/3 Please update the IOS to enable the "macro" command! Warning: You are using an old IOS image for this router. To view existing vlans use the command "show vlan-switch brief" To create vlans use the command "vlan database" from exec modeĪfter creating all desired vlans use "exit" to apply the config It has been preconfigured with hard coded speed and duplex This is a normal Router with a SW module inside (NM-16ESW) You can see that pinging between VPCS is successful.ĭescription *** Unused for Layer2 EtherSwitch *** ESW1# conf tĮSW1(config-if)#ip address 192.168.10.1 255.255.255.0Ĭonfigure the VPCS and then ping the VLAN1 interface to test the connection as follows. Now, to test the Switch, execute the show vlan-switch command in the CLI command interface.Ĭonfigure the switch by executing the following commands. Wait while calculating the Idle-PC value.Īfter determining the optimal Idle-PC value for IOS, click OK to continue.Īs you can see in the image below, the Layer 3 Switch (EtherSwitch Router) has added successfully.ĭrag and drop the Switch to the GNS3 workspace.Ĭreate a topology as follows and double click on 元 Switch. In the Network Adapters window, select the NM-16ESW interface in Slot 0 and continue to the next step.Ĭlick the Idle-PC Finder button to select the optimal value for your computer’s processor performance for Layer 3 Switch IOS. Leave the RAM value of Layer 3 Switch as default and click Next. In this step, select “ This is an EthernetSwitch Router” and then click Next. The GNS3 program asks if you want to copy the IOS to the default image folder, click Yes.Īfter adding Switch IOS, click Next to continue. Select the IOS you downloaded from the above button and click the Open button. In the IOS Image window, select New Image, then click Browse. To add 元 Switch, click the New button in the IOS Router templates window. Previously we added L2 Switch from Qemu VMs. ![]() ![]() ![]() In the General Preferences window, click the IOS Routers tab. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |